Using Lyapunov's direct method for wave suppression in reactive systems

This paper proposes a new approach for stabilizing a homogeneous solution in reaction–convection–diffusion system with oscillatory kinetics, in which moving or stationary patterns emerge in the absence of control. Specifically, we aim to suppress patterns by using a spatially weighted finite-dimensional feedback control that assures stability of the solution according to Lyapunov's direct method. A practical design procedure, based on spectral representation of the system and dissipative nature of parabolic PDEs, is presented.     

MS方法的一个新证明及其结构优化算法

本文给出Ｍｉｌｎｅ－Ｓｉｍｐｓｏｎ（ＭＳ）预测─校正法新的导出方法，并以结构优化思想设计出通用性和可靠性较强的算法。     

倒虹吸管管径计算的迭代法

本文先将倒虹吸管的管径计算公式整理成等式左边只含管径的一次方法，右边含有管径高阶非线性的迭代函数，然后证明该迭代函数收敛，最后利用数学迭代原理给迭代函数右边赋初值，计算左边的管径。继续迭代下去，就能求出倒虹吸管的管径。     

智能混合控制在高速纸机的应用

介绍了压力式网前箱的建模和控制，并通过构造一个新的控制器结构-智能混合控制器，将Fuzzy和PID控制融于其中。     

梯度相关法测量两相流流量的精度与离散性研究

借助一种新的传感器布置与信号处理方法,能够测量真正的平均流速与流量。通过对气一固两相流体的实验研究,证明了梯度相关理论与实验相符。针对长时间连续测量中出现的互协方差梯度波动问题,对光学传感器的数学模型与互协方差梯度计算方法进行了修正,提高了测量精度。     

Application of boundary element method to 3-D problems of coupled thermoelasticity

This paper deals with a new boundary element method for analysis of the quasistatic problems in coupled thermoelasticity. Through some mathematical manipulation of the Navier equation in elasticity, the heat conduction equation is transformed into a simpler form, similar to the uncoupled-type equation with the modified thermal conductivity which shows the coupling effects. This procedure enables us to treat the coupled thermoelastic problems as an uncoupled one, A few examples are computed by the proposed BEM, and the results obtained are compared with the analytical ones available in the literature, whereby the accuracy and versatility of the proposed method are demonstrated.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

步进梁式炉的运动研究

对国内引进的、用于粉末冶金的步进梁式炉的运动,以图解法和解析法进行了分析,并对运动参数进行了理论推导和计算。本研究结果,对解决步进粱式炉的运动故障以及进行新型设计提供了有效的理论分析和计算依据。     

双戗堤截流时下戗堤的作用分析

立堵截流计算的核心内容是龙口流速的求取，因为龙口流速的大小直接影响到截流时所选择抛投料粒径的大小，可以说是衡量截流难度的一个重要指标。本文在分析单戗堤立堵截流龙口流速变化规律的基础上，着重研究了在双戗堤立堵截流中，当上戗堤最困难的时候，也就是流速最大的时候，下戗堤是否能够壅水，从而降低上戗堤的截流难度这个问题，论证了双戗堤立堵截流水力控制条件的正确性，为双戗堤立堵截流的顺利施工提供判断依据一     

New approaches for error estimation and adaptivity for 2D potential boundary element methods

This work presents two new error estimation approaches for the BEM applied to 2D potential problems. The first approach involves a local error estimator based on a gradient recovery procedure in which the error function is generated from differences between smoothed and non‐smoothed rates of change of boundary variables in the local tangential direction. The second approach involves the external problem formulation and gives both local and global measures of error, depending on a choice of the external evaluation point. These approaches are post‐processing procedures. Both estimators show consistency with mesh refinement and give similar qualitative results. The error estimator using the gradient recovery approach is more general, as this formulation does not rely on an ‘optimal’ choice of an external parameter. This work presents also the use of a local error estimator in an adaptive mesh refinement procedure. This r‐refinement approach is based on the minimization of the standard deviation of the local error estimate. A non‐linear programming procedure using a feasible‐point method is employed using Lagrange multipliers and a set of active constraints. The optimization procedure produces finer meshes close to a singularity and results that are consistent with the problem physics. Copyright © 2002 John Wiley & Sons, Ltd.